I. Paper feed department (independent front feed department)
1, Machine clutch
〖1〗Electric control clutch with alarm bell, continuous ringing
during its proceeding to ensure the safety of operators.
〖2〗The transmission shaft is attached with a friction clutch to
avoid damaging the machine due to misoperation.
〖3〗Pneumatic interlock device.
〖4〗The main motor adopts frequency conversion motor, frequency
conversion control, energy saving, stable start, with motor start
protection device.
2,Leading edge feed system
〖1〗Suction auxiliary paper feeding, fan 7.5kW, can adjust the air
volume according to the different bending conditions of the
paperboard to ensure the smooth paper feeding.
〖2〗The die cutting part is equipped with interlock control switch
to control the urgent stop feeding.
〖3〗Paper lifting and paper dropping are driven by air cylinder,
which is fast and labor-saving.
〖4〗The leading edge roller feeding system can greatly improve the
feeding stability of the bending board.
〖5〗Electric adjustment of left and right side baffle position,
manual adjustment of front baffle clearance, electric adjustment of
rear baffle position.
〖6〗Feeding counter, sets and displays the production quantity.
- Dust removal device
〖1〗The brush dedusting device in the paper feeding part can remove
a lot of impurities on the printing surface of the paperboard and
improve the printing quality.
4,Paper feeding roller
〖1〗The outer diameter of the upper roll is ￠ 140 mm.
〖2〗Solid steel, wrapped with wear-resistant rubber, and balanced.
〖3〗Lower roll ￠156 mm embossed hard chrome plating, and do balance
correction.
〖4〗The paper feeding roller gap dial is adjusted manually, with the
adjustment range of 2-11mm.
5,Automatic zeroing device
〖1〗Paper feeding section, printing section, slotting section,
electric automatic zero.
Slotting Department (computer cutter)
1,Pressing device
〖1〗The shaft diameter is ￠ 110mm, the surface is ground, hard
chrome plated, and the movement is stable.
〖2〗Make balance correction, and run smoothly.
〖3〗Manually adjust the clearance dial of the pressing wheel, with
the adjustment range of 0-12mm.
2,Slotting tool block Horizontal Adjustment mechanism
〖1〗The shaft diameter is ￠ 154mm, the surface is ground, hard
chrome plated, and the movement is stable.
〖2〗The width of slotting knife is 7mm.
〖3〗Alloy steel material after heat treatment grinding tooth
slotting knife, good hardness and toughness.
〖4〗Alloy steel material after heat treatment grinding trimming
knife, sharp edge, high precision.
〖5〗Adjust the traverse position of pressing wheel and slotting
cutterbed, and adopt the electric mechanical joint adjustment
〖6〗The height of the box is adjusted to the structure of manual
synchronous tool adjustment.
3,Slotting phase adjusting mechanism
〖1〗Planetary gear construction
〖2〗The slotting phase is controlled by electric digital 360°.
(operation and stop can be adjusted)
XT-Z Series Main Technical Parameter
| Item | Unit | 2800style |
| Inside width of baffles | mm | 2800 |
| Inside width of baffles | mm | 1270×2600 |
| Effective printing | mm | 1200×2400 |
| Minimum machining size | mm | 320×640 |
| Thickness of printing plate | mm | 7.2 |
| Working speed | sheets/min | 0-150 |
| Main motor power | KW | 18.5～30 |
| Total power | KW | 30～45 |
| Weight | T | ～22 |
| Die cutting accuracy | mm | ± 1.5 |
| Register accuracy | mm | ±0.5
|
